laser_cutter_training_sop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
laser_cutter_training_sop [2023/07/17 23:09] – rylin | laser_cutter_training_sop [2023/09/12 22:01] (current) – [Material] bdincau | ||
---|---|---|---|
Line 61: | Line 61: | ||
* ABS (acrylonitrile butadiene styrene) | * ABS (acrylonitrile butadiene styrene) | ||
* Acrylic (also known as Plexiglas, Lucite, PMMA) | * Acrylic (also known as Plexiglas, Lucite, PMMA) | ||
- | * Delrin (POM, acetal) — for a supplier, try www.mcmaster.com. | + | * Delrin (POM, acetal) — **Must use nitrogen assist when cutting delrin** |
* Kapton tape (Polyimide) | * Kapton tape (Polyimide) | ||
* Mylar (polyester) | * Mylar (polyester) | ||
Line 165: | Line 165: | ||
|} | |} | ||
- | ====Functional Engraving Recipes==== | + | ====General |
- | For users looking to cut acrylic at different depths, different cut depths were tested with different power settings. | + | |
- | + | ||
- | {| style="" | + | |
- | |+ | + | |
- | ! | + | |
- | Engraving Cut Thickness | + | |
- | ! | + | |
- | Engraving Settings | + | |
- | |- | + | |
- | | | + | |
- | 0 mm | + | |
- | | | + | |
- | 0% power, 0% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.208 mm | + | |
- | | | + | |
- | 50% power, 30% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.314 mm | + | |
- | | | + | |
- | 60% power, 30% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.352 mm | + | |
- | | | + | |
- | 70% power, 30% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.413 mm | + | |
- | | | + | |
- | 80% power, 30% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.446 mm | + | |
- | | | + | |
- | 90% power, 30% speed | + | |
- | |- | + | |
- | | | + | |
- | 0.485 mm | + | |
- | | | + | |
- | 100% power, 30% speed | + | |
- | |} | + | |
- | + | ||
- | For users who wish to cut at different depths than those listed above, here is a graph and equation that may help out with making estimations of what laser power to use. | + | |
- | + | ||
- | {{functional_acrylic_engraving.jpg? | + | |
- | + | ||
- | ====General | + | |
{| style="" | {| style="" | ||
|+ | |+ | ||
Line 221: | Line 171: | ||
Thickness | Thickness | ||
! | ! | ||
- | Curf Width | + | Kerf Width |
|- | |- | ||
| | | |
laser_cutter_training_sop.1689635360.txt.gz · Last modified: 2023/07/17 23:09 by rylin