crystalmarksop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
crystalmarksop [2023/07/19 18:18] – colin | crystalmarksop [2024/01/22 17:54] (current) – [Rates] bdincau | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Crystalmark Training SOP====== | ====== Crystalmark Training SOP====== | ||
- | Last edited: | + | Last edited: |
- | Tool Lead: [PLACEHOLDER]\\ | + | Tool Lead: Yanis Yankauskas\\ |
- | Contact: | + | Contact: |
- | + | ||
- | ====== CrystalMark ====== | + | |
====Training Checklist: | ====Training Checklist: | ||
Line 35: | Line 33: | ||
- Turn on CrystalMark DV-1 (under table) | - Turn on CrystalMark DV-1 (under table) | ||
- Plug in camera to computer (USB connection) | - Plug in camera to computer (USB connection) | ||
- | - fixture | + | - Fixture |
There are two ways to use the CNC: Etching with a .dxf file or manually etching: using .dxf file or manually \\ | There are two ways to use the CNC: Etching with a .dxf file or manually etching: using .dxf file or manually \\ | ||
Line 45: | Line 43: | ||
- open .ngc in " | - open .ngc in " | ||
- open " | - open " | ||
- | - Jog the CNC down to the surface of your piece, use a piece of paper to shim the etching nozzle and piece | + | |
- | - " | + | - Jog the nozzle into the hole |
+ | - " | ||
+ | | ||
+ | - " | ||
+ | - After zero-ing the Z axis, move up in Z until Z is at 1.1 mm. This will be your cutting height. | ||
- Select " | - Select " | ||
- " | - " | ||
- Note that origin is displayed in "DXF to G-Code Converter" | - Note that origin is displayed in "DXF to G-Code Converter" | ||
+ | - Use tape and/or turn on vaccum to fixture part (optional) | ||
- Begin etching : " | - Begin etching : " | ||
- Monitor operation | - Monitor operation | ||
Line 57: | Line 60: | ||
- open " | - open " | ||
- open " | - open " | ||
- | - Jog the CNC down to the surface of your piece, use a piece of paper to shim the etching nozzle and piece | + | |
- | - " | + | - Jog the nozzle into the hole |
- | - Select " | + | - " |
+ | | ||
+ | - " | ||
+ | - After zero-ing | ||
+ | - Use tape and/or turn on vaccum to fixture part (optional) | ||
- Select " | - Select " | ||
- Let the Etcher create a through hole | - Let the Etcher create a through hole | ||
Line 75: | Line 82: | ||
* Use ShopVac to vacuum excess aluminum oxide | * Use ShopVac to vacuum excess aluminum oxide | ||
* Dispose of excess sharps in sharps container | * Dispose of excess sharps in sharps container | ||
- | * Unlug camera, close air valve, turn off FlashCut CNC, turn off CrytalMark DV1 | + | * Unplug |
====Maintenance==== | ====Maintenance==== | ||
- | * ShopVac | + | * Vacuum |
====Additional Information==== | ====Additional Information==== | ||
+ | You can record your cuts in DinoCapture | ||
====Troubleshooting==== | ====Troubleshooting==== | ||
- | Work in Progress | + | If the Crystalmark is not cutting, the abrasive canister may be empty. Please |
- | + | contact workshop staff to refill tool. | |
- | ====Rates==== | + | |
- | CrystalMark: | + | |
- | Work in Progress |
crystalmarksop.1689790713.txt.gz · Last modified: 2023/07/19 18:18 by colin