Differences

This shows you the differences between two versions of the page.

--- waterjetsop [2023/09/19 18:27] – yanis
+++ waterjetsop [2023/09/26 23:20] (current) – [Cutting with the Wazer Waterjet] bdincau
@@ Line 61: / Line 61: @@
 ====Cutting with the Wazer Waterjet====
-  - **Open WAM**. This is where you will create the toolpath for your job. Upload your DXF or SVG file onto the software, and export it via SD card.
+  - **Open WAM**. This is where you will create the toolpath for your job.
-    - Scale and position your material. Importing the file may result in a change in dimensions, so double check the measurements are still the same.
+    - Upload your DXF or SVG file onto the software.
-    - The waterjet has the origin set to the top left corner of the machine. The top-left corner of the toolpath inserted will become the new origin and where the nozzle will move to after the homing sequence.
+    - Scale and position your parts. Importing the file may result in a change in dimensions, so double check the measurements are still the same.
+    - The grid in the software matches the plastic cut bed in the Wazer. Move your part(s) so that they will fit within your material.
     - Select the material you are working with and select the corresponding thickness. If you do not see the material you are cutting, contact a wizard.
-    - Select the cutting path offset. This will allow you to control how the kerf will affect your cut.
+    - Select the cutting path offset. This will allow you to control how the kerf will affect your cut (don't change the default unless you know how to adjust it).
     - Select your tabs and leads. This will prevent vibration/pop-ups, which will jam the waterjet and ruin the cut, and also improve accuracy.
+      - Usually 2-4 tabs is enough for most materials and thicknesses.
+      - Tab thickness should be proportional to material thickness, a good rule of thumb is for your tab thickness to be 30-50% of your material thickness. For very thin materials, we recommend a minimum tab thickness of 0.05"
     - Select the cut quality. This will determine time for each job and the amount of abrasive used.
-  - **Check water bed level**. Make sure the water level is nearly up to the top of the bed (within 2 mm or so). If there is not enough water, add some more with the rubber hose connected to the DI water. Insufficient water levels will not allow the waterjet to turn on.
+      - Fine usually gives the best results
+  - **Check water bed level**. Make sure the water level is nearly up to the top of the bed (within 2 mm or so). If there is not enough water, add some more with the rubber hose connected to the DI water. Insufficient water levels will not allow the waterjet to turn on.{{ :tools:wazer_waterjet:img-1579.jpg?200|}}{{ :tools:wazer_waterjet:img-1578.jpg?200|}}
   - **Check Abrasives**.
      - Fill up the abrasive tanks to the top of the sieve (drawer on the left side of the waterjet).
-     - Empty the used abrasive tanks into the trash (under the cover closest to the front inside the wazer).
+       - The bucket of abrasive is under the sink. The backup bucket(s) are on the right of the F270.
-  - **Turn on Water and Power Supplies**.
+     - Empty the used abrasive tanks into the trash (under the cover closest to the front inside the wazer).
-    - Turn the sink handle on, you should see the filter water pressure jump up.
+  - **Turn on Water and Power Supplies**.{{ :tools:wazer_waterjet:img-1580.jpg?200|}}
-      - If there are any signs of leaks, turn off the water immediately and notify a wizard. Make sure the power supplies have a green light on. If not, try pressing reset.
+    - Turn the sink handle on, you should see the filter water pressure jump up. Ensure that the pressure gauge is in the green, if it's not there isn't enough water flow and you CANNOT CUT.
+      - If there are any signs of leaks, turn off the water immediately and notify a wizard.
+    - Check that the drain hose is going into the sink.
     - Turn on the wazer and pump by pressing the "reset" button on the power blocks (bottom right and top left relative to the wazer).
   - **Insert SD Card, Turn On, and Select Cut File**. The power switch is located towards the front on the right underside of the wazer. Select your cut file. Go through the steps on the screen.
@@ Line 93: / Line 99: @@
     - If everything is OK, click the play button and your part will begin to print.
   - **YOU MUST NOT LEAVE WHILE PART IS BEING CUT**
-  - Once the print has been completed, open the lid, lower the bed and remove the part. Beware of sharp edges. Make sure all pieces of material are removed from bed.
+  - Once the print has been completed, open the lid, unscrew your material, and remove the part. Beware of sharp edges. Make sure all pieces of material are removed from bed.
-  - **Tank Cleaning and Maintenance**. Run a tank cleaning cycle if you are not making another cut for a while or if the machine has been running for more than 4 hours. This will collect abrasive that is at the bottom of the tank. There will be some abrasive that accumulates from the door windows and on the bellows. If they are not coming off easily, let them dry and then sweep.
+  - **Turn off the printer**
-  - **Turn off the printer** and leave the lid open.
+    - Press test on both the power supplies.
+    - Close the sink lever and ensure that the pressure drops in the filter gauge (it won't go all the way down to to 0)
+    - Leave the wazer lid open.
 ====Troubleshooting====