Differences

This shows you the differences between two versions of the page.

--- formwash_cleaner [2026/02/04 18:29] – [Operating Procedures] colin
+++ formwash_cleaner [2026/02/04 18:47] (current) – [Operating Procedures] colin
@@ Line 1: / Line 1: @@
-====== FormWash Cleaner======
+====== Form Wash Cleaner======
-^       FormWash        ^
+^       Form Wash        ^
-|         {{::formwashv2.png?400|}}      |
+|         {{::formwashv2.png?300|}}      |
 | **Tool Type:**                  Post-processing                          |
 | **Location:**                   Elings 3430                           |
@@ Line 10: / Line 10: @@
 | **Manufacturer:**               FormLabs                           |
-Last updated 1/5/23 Haley
+Last updated 2/4/26 Colin
 ----
 ===== About =====
-The FormWash is a post processor for the Form 2 resin 3D printers. Using an alcohol bath, build trays and/or parts can be loaded into the FormWash where all uncured resin from the surface of the prints is removed.
+The Form Wash is a post processor for the Formlabs resin 3D printers. Using an alcohol bath, build trays and/or parts can be loaded into the Form Wash where all uncured resin from the surface of the prints is removed.
 ----
@@ Line 21: / Line 21: @@
 ===== Safety Concerns =====
-FormWash contains large amounts of IPA, a flammable solvent. Keep away from any possible sources of heat or sparks. Filling the FormWash should only be done by a Workshop Wizard within the fume hood.
+Form Wash contains large amounts of IPA, a flammable solvent. Keep away from any possible sources of heat or sparks. Filling the Form Wash should only be done by a Workshop Wizard within the fume hood.
 ----
@@ Line 28: / Line 28: @@
   - Remove build platform from Formlabs 3D printer, making sure to keep a tray under the platform to prevent drips
   - Wake the Form Wash using the large dial located bottom right of the front face, select "OPEN"
-  - Load the build platform onto the mount arms. Adjust the position of the mount arms according to the size of the platform. (see below reference picture)
+  - Load the build platform onto the mount arms. Adjust the position of the mount arms according to the size of the platform. (see reference picture below) \\ {{:formwashv2mountarms.png?200|}}
-{{:formwashv2mountarms.png?200|}}
   - If prints were removed prints from build platform, load them into Form Wash basket.
   - Using the dial select the desired amount of time, click "START"
@@ Line 39: / Line 38: @@
 ===== Detailed Specifications =====
-  * Max part size: 14.5 x 14.5 x 17.5 cm
+  * Max part size: 20 x 14.5 x 19.5 cm
-  * 8.6 L IPA to fill completely
+  * 14 L IPA to fill completely
 ----
 ===== Reference Documentation =====
-[[form2sop|Form 2 Training SOP]]
+{{ :form_4_sop.pdf | Form 4 SOP}}
-[[https://support.formlabs.com/s/article/Using-Form-Wash?language=en_US]]
+[[https://support.formlabs.com/s/article/Receiving-and-setting-up-the-Form-Wash-2nd-Generation?language=en_US|FormWash Setup]]
-[[https://support.formlabs.com/s/article/Form-Wash-Time-Settings?language=en_US]]
+[[https://support.formlabs.com/s/article/Form-Wash-Time-Settings?language=en_US|FormWash Times]]
 ----