whatprintershouldiuse
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
whatprintershouldiuse [2021/01/13 17:47] – furst | whatprintershouldiuse [2023/08/02 18:38] (current) – rylin | ||
---|---|---|---|
Line 1: | Line 1: | ||
=====Which 3D Printer is Best for my part?===== | =====Which 3D Printer is Best for my part?===== | ||
- | Depending on the geometry of a part, its application, | + | Depending on the geometry of a part, its application, |
+ | |||
+ | =====Ultimaker===== | ||
+ | The Ultimaker printers are FDM filament-fed 3D printers. Each has two extruders set up with build and support material with a tip width of .25,.4,.6 and .8 mm available. Layer lines are visible with this printer with slice heights of 60-200 micron, and this printer can print variable infill from 10% to 100%. | ||
- | ====Ultimaker==== | ||
Default material: ABS (orange) & PVA (dissolvable) | Default material: ABS (orange) & PVA (dissolvable) | ||
Line 10: | Line 12: | ||
* PLA | * PLA | ||
* PVA (dissolvable support) | * PVA (dissolvable support) | ||
- | * nylon | + | * Nylon |
* CPE | * CPE | ||
- | * Flexable | + | * Flexible |
- | * Cheep and easy to run printer | + | * Cheap and easy to run printer |
* Easy to switch filaments | * Easy to switch filaments | ||
* Capable of creating large overhangs with less support filament (tree support) | * Capable of creating large overhangs with less support filament (tree support) | ||
- | | + | |
**Cons:** | **Cons:** | ||
* Requires post processing | * Requires post processing | ||
- | * Susceptible to warping due to moisture | + | * Susceptible to warping due to moisture |
+ | * Most likely printers to fail | ||
+ | ----- | ||
- | ====F270==== | + | =====F270===== |
- | Default material: ABS (blue) & SQR (support) | + | The F270 is also a dual extruder FDM filament fed printer typically set up with build and support material. Layer lines are visible with variable slice height from 127-330 micron. Variable infill from 10%-100% is available. |
+ | |||
+ | |||
+ | Default material: ABS, ASA, QSR (dissolvable | ||
**Pros:** | **Pros:** | ||
* Quick easy printing resulting in fast turn around time | * Quick easy printing resulting in fast turn around time | ||
* Capable of printing the largest prints (305x254 mm) | * Capable of printing the largest prints (305x254 mm) | ||
+ | * Extremely reliable | ||
+ | * Produces strong even parts due to heated chamber | ||
+ | |||
**Cons:** | **Cons:** | ||
- | * Difficult | + | * Relatively poor resolution for small parts (~1mm) |
+ | * Typically requires post process bath to remove support material | ||
+ | |||
+ | ----- | ||
+ | =====Form 3===== | ||
+ | The Form 3 printer is a SLA resin printer capable of very high precision. Using UV light to cure the resin bath, layer lines are less pronounced with slice heights from 25-100 microns depending on the resin. | ||
- | ====Form 2==== | + | Default material: |
- | Default material: | + | |
**Pros:** | **Pros:** | ||
+ | * Many material choices | ||
+ | * Clear | ||
+ | * White | ||
+ | * Durable | ||
+ | * Tough | ||
+ | * Flexible | ||
+ | * Black (and many more) | ||
* Able to produce optically clear parts | * Able to produce optically clear parts | ||
- | * | + | * Able to produce sharp points/thin risers |
+ | * Very reliable for standard prints | ||
**Cons:** | **Cons:** | ||
* Chance of print failure if positioned incorrectly | * Chance of print failure if positioned incorrectly | ||
+ | * Requires post processing to remove supports | ||
+ | * Can develop slight warping on thin parts during curing | ||
+ | ----- | ||
- | ====Objet==== | + | =====Objet30 Pro===== |
Default material: RGD450 & support | Default material: RGD450 & support | ||
**Pros:** | **Pros:** | ||
- | * Able to produce smooth high quality surface finish | + | * Able to produce smooth high quality surface finish on the top face (good for molds) |
* Requires very little post processing | * Requires very little post processing | ||
* Low chance of print failure | * Low chance of print failure | ||
+ | |||
**Cons:** | **Cons:** | ||
* Highest material cost of all printers | * Highest material cost of all printers | ||
* Slow printing time | * Slow printing time | ||
+ | * Produces slightly rounded edges, due to the nature of polyjet printing. | ||
+ | |||
+ | ----- | ||
- | WORK IN PROGRESS |
whatprintershouldiuse.1610560067.txt.gz · Last modified: 2021/01/13 17:47 by furst