sherline_cnc_mill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
sherline_cnc_mill [2023/01/05 02:31] – haley | sherline_cnc_mill [2023/07/18 20:03] (current) – rylin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Flashcut / Sherline CNC Mill ====== | + | ====== Flashcut / Sherline CNC Drill ====== |
- | Haley Holcomb 9/12/22 | + | |
- | ^ Flashcut / Sherline | + | ^ |
| {{ : | | {{ : | ||
- | | **Tool Type: | + | | **Tool Type: |
- | | **Location: | + | | **Location: |
- | | **Supervisor** | + | | **Description: |
- | | David Bothman | + | | **Manufacturer: |
- | | (805) 893-4125 | + | |
- | | bothman@cnsi.ucsb.edu | + | |
- | + | ||
- | | **Description: | + | |
- | | **Manufacturer: | + | |
+ | Last updated 9/12/22 Haley | ||
---- | ---- | ||
===== About ===== | ===== About ===== | ||
- | CNC diamond drill used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations. | + | The CNC diamond drill is used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations. |
---- | ---- | ||
Line 36: | Line 31: | ||
===== Detailed Specifications ===== | ===== Detailed Specifications ===== | ||
- | * Stepper motor mounts and couplers on X-, Y- and Z--axes | + | * Stepper motor mounts and couplers on X-, Y- and Z-axes |
* 70-2800 RPM continuously variable by electronic speed control | * 70-2800 RPM continuously variable by electronic speed control | ||
* Maximum CNC travel positioning speed: 22 in/min | * Maximum CNC travel positioning speed: 22 in/min | ||
Line 46: | Line 41: | ||
- | ===== Sample G-code ===== | ||
- | (Sample program to drill six holes on the Microfluidics Lab Drill) | ||
- | (Dave Bothman, 2 July 2012) | ||
- | |||
- | (Change x,y coordinates of G73 commands for your hole coordinates) | ||
- | |||
- | |||
- | (Setup blocks) | ||
- | |||
- | G21 (select mm units) | ||
- | |||
- | G49 G80 G90 (cancel offsets, cancel cycles, absolute coordinates) | ||
- | |||
- | G98 (Move the drill away from the part when drilling is finished) | ||
- | |||
- | G00 X0 Y0 Z5 (move to the lower left corner of slide, 5mm above) | ||
- | |||
- | |||
- | (Hole drilling blocks) | ||
- | |||
- | G73 X22.5 Y12.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | G73 X29.5 Y4.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | G73 X45.5 Y4.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | G73 X52.5 Y12.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | G73 X45.5 Y20.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | G73 X29.5 Y20.5 Z-1.2 Q.1 R0.5 F5 | ||
- | |||
- | |||
- | |||
- | (Closing block) | ||
- | |||
- | M30 | ||
- | |||
- | |||
- | ---- | ||
===== Reference Documentation ===== | ===== Reference Documentation ===== |
sherline_cnc_mill.1672885877.txt.gz · Last modified: 2023/01/05 02:31 by haley