sherline_cnc_mill
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
sherline_cnc_mill [2022/09/12 22:30] – [Operating Procedures] haley | sherline_cnc_mill [2023/07/18 20:03] (current) – rylin | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Flashcut / Sherline CNC Mill ====== | + | ====== Flashcut / Sherline CNC Drill ====== |
- | Haley Holcomb 8/26/22 | + | |
- | ^ Flashcut / Sherline | + | ^ |
| {{ : | | {{ : | ||
- | | **Tool Type: | + | | **Tool Type: |
- | | **Location: | + | | **Location: |
- | | **Supervisor** | + | | **Description: |
- | | David Bothman | + | | **Manufacturer: |
- | | (805) 893-4125 | + | |
- | | bothman@cnsi.ucsb.edu | + | |
- | + | ||
- | | **Description: | + | |
- | | **Manufacturer: | + | |
+ | Last updated 9/12/22 Haley | ||
---- | ---- | ||
===== About ===== | ===== About ===== | ||
- | CNC diamond drill used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations. | + | The CNC diamond drill is used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations. |
---- | ---- | ||
- | ===== Detailed Specifications | + | ===== Safety Concerns |
- | + | Eye injuries can result from flying chips or broken bits. Cuts can occur from contacting sharp tools or broken glass. Burns can result from hot cutting tools or parts. Serious injury can result from pinching or entanglement in moving parts. Poor housekeeping creates tripping and cutting hazards for other users. Do not leave machine running unattended. Eye protection, closed toe shoes, long pants, and protective clothing must be worn when using this machine to prevent injury. Long hair must be tied back and jewelry must be removed before operating this machine to prevent entanglement. | |
- | Insert Text Here! | + | |
---- | ---- | ||
- | ===== Safety Concerns | + | ===== Training Documentation |
- | Insert Text Here! | + | [[Sherline Training SOP|]] |
---- | ---- | ||
- | ===== Sample G-code | + | ===== Detailed Specifications |
- | (Sample program | + | * Stepper motor mounts and couplers on X-, Y- and Z-axes |
- | (Dave Bothman, 2 July 2012) | + | * 70-2800 RPM continuously variable by electronic speed control |
- | (Change | + | * Maximum CNC travel positioning speed: 22 in/min |
- | (Setup blocks) | + | * Max clearance |
- | G21 (select | + | * Travel axes x,y,z: 8.65″ |
- | G49 G80 G90 (cancel offsets, cancel cycles, absolute coordinates) | + | * CNC Stepper motor holding torque: 136 oz-in |
- | G98 (Move the drill away from the part when drilling is finished) | + | |
- | G00 X0 Y0 Z5 (move to the lower left corner of slide, 5mm above) | + | ---- |
- | (Hole drilling blocks) | ||
- | G73 X22.5 Y12.5 Z-1.2 Q.1 R0.5 F5 | ||
- | G73 X29.5 Y4.5 Z-1.2 Q.1 R0.5 F5 | ||
- | G73 X45.5 Y4.5 Z-1.2 Q.1 R0.5 F5 | ||
- | G73 X52.5 Y12.5 Z-1.2 Q.1 R0.5 F5 | ||
- | G73 X45.5 Y20.5 Z-1.2 Q.1 R0.5 F5 | ||
- | G73 X29.5 Y20.5 Z-1.2 Q.1 R0.5 F5 | ||
- | (Closing block) | ||
- | M30 | ||
- | |||
- | ---- | ||
===== Reference Documentation ===== | ===== Reference Documentation ===== | ||
Line 73: | Line 56: | ||
{{: | {{: | ||
----- | ----- | ||
- | ===== Training Documentation ===== | ||
- | |||
- | Insert Text Here! | ||
- | ---- | ||
sherline_cnc_mill.1663021828.txt.gz · Last modified: 2022/09/12 22:30 by haley