Differences

This shows you the differences between two versions of the page.

--- sherline_cnc_mill [2022/09/12 22:34] – [Flashcut / Sherline CNC Mill] haley
+++ sherline_cnc_mill [2023/07/12 16:30] – rylin
@@ Line 1: / Line 1: @@
-====== Flashcut / Sherline CNC Mill ======
+====== Flashcut / Sherline CNC Drill ======
-Haley Holcomb 9/12/22
-^             Flashcut / Sherline CNC Mill                              ^
+^             CNC Diamond Drill                              ^
 |     {{ :tools:sherlinecncmill:sherline_cnc_mill.jpg?nolink&200 |}}    |
-| **Tool Type:**                  "CNC"                           |
+| **Tool Type:**                  CNC                           |
-| **Location:**                   "mFL 3430"                           |
+| **Location:**                   Microfluidics Lab                           |
-|  **Supervisor**        |  **Tool Lead**  |
+| **Description:**                CNC diamond drill for glass slides                          |
-|  David Bothman         |  Haley Holcomb  |
+| **Manufacturer:**               Sherline                           |
-|  (805) 893-4125        |  (415)-320-3279 |
-|  bothman@cnsi.ucsb.edu  |  haleyholcomb@ucsb.edu  |
-| **Description:**                "CNC Diamond Drill"                           |
-| **Manufacturer:**               "Sherline"                           |
+Last updated 9/12/22 Haley
 ----
 ===== About =====
-CNC diamond drill used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations.
+The CNC diamond drill is used to drill holes in glass slides. Uses FlashCut CNC software to interpret G-code and drill holes in programmed locations.
-----
-===== Detailed Specifications =====
-Insert Text Here!
 ----
@@ Line 34: / Line 24: @@
 ----
-===== Sample G-code =====
+===== Training Documentation =====
-(Sample program to drill six holes on the Microfluidics Lab Drill)
-(Dave Bothman, 2 July 2012)
+[[Sherline Training SOP|]]
-(Change x,y coordinates of G73 commands for your hole coordinates)
+----
+===== Detailed Specifications =====
+  * Stepper motor mounts and couplers on X-, Y- and Z--axes
+  * 70-2800 RPM continuously variable by electronic speed control
+  * Maximum CNC travel positioning speed: 22 in/min
+  * Max clearance (table to spindle): 8.00″ (203 mm)
+  * Travel axes x,y,z: 	8.65″ (220 mm), 5.00″ (127 mm), 6.25″ (159 mm)
+  * CNC Stepper motor holding torque: 136 oz-in
-(Setup blocks)
+----
-G21 (select mm units)
-G49 G80 G90 (cancel offsets, cancel cycles, absolute coordinates)
-G98 (Move the drill away from the part when drilling is finished)
-G00 X0 Y0 Z5 (move to the lower left corner of slide, 5mm above)
-(Hole drilling blocks)
-G73 X22.5 Y12.5 Z-1.2 Q.1 R0.5 F5
-G73 X29.5 Y4.5 Z-1.2 Q.1 R0.5 F5
-G73 X45.5 Y4.5 Z-1.2 Q.1 R0.5 F5
-G73 X52.5 Y12.5 Z-1.2 Q.1 R0.5 F5
-G73 X45.5 Y20.5 Z-1.2 Q.1 R0.5 F5
-G73 X29.5 Y20.5 Z-1.2 Q.1 R0.5 F5
-(Closing block)
-M30
-----
 ===== Reference Documentation =====
@@ Line 89: / Line 56: @@
 {{:tools:sherlinecncmill:sample_g-code.rtf|Sample G-Code}}
 -----
-===== Training Documentation =====
-Insert Text Here!
-----