Differences

This shows you the differences between two versions of the page.

--- sca_naoh_bath [2020/10/08 17:08] – [Detailed Specifications] furst
+++ sca_naoh_bath [2023/01/06 01:31] (current) – [SCA 1200 HT NaOH Parts Bath] haley
@@ Line 1: / Line 1: @@
-====== SCA 1200 HT NaOH parts bath ======
+====== SCA 1200 HT NaOH Parts Bath ======
-^                                    SCA 1200 HT NaOH parts bath         ^
+^                                    NaOH Bath         ^
 |           {{:tools:scanaohbath:scanaohbath.jpg?200|}}        |
-| **Tool Type:**                  "3D print support Dissolve"                           |
+| **Tool Type:**                  Post-processing                           |
-| **Location:**                   "TEXT HERE"                           |
+| **Location:**                   Innovation Workshop                          |
-|  **Supervisor**        |  **Tool Lead**  |
-|  David Bothman         |  "WW Name"  |
-|  (805) 893-4125        |  (###) ###-####  |
-|  bothman@cnsi.ucsb.edu  |  "WW Email"  |
-| **Description:**                "Dissolves support filament for F270"                           |
+| **Description:**                NaOH bath for dissolving F270 support material                          |
-| **Manufacturer:**               "PADT"                           |
+| **Manufacturer:**               PADT                          |
+Last updated 1/5/23 Haley
 ----
 ===== About =====
-This tool is used to dissolve the support filament printed by the F270 FDM 3D printer. Using a heated solvent, parts can be loaded into the main bucket or suspended in a smaller cage during the support removal process.
+This tool is used to dissolve the support filament printed by the Stratysys F270 FDM 3D printer. Parts can be loaded into the main bucket or suspended in a smaller cage during the support removal process.
-----
-===== Detailed Specifications =====
-  * Available Temperatures: 50, 60, 70, 85 degrees C
-  * Auto overfill alarm
-  * 46.3 L tank
 ----
@@ Line 32: / Line 22: @@
 ===== Safety Concerns =====
-This tool makes use of a heated solvent! A lab coat, face shield, and nitrile gloves must be wore by the user whenever the SCA 1200 HT is to be opened to protect for solution and vapor fumes. In case of contact with solution flush eyes, and skin with water, remove all contaminated clothing, and get medical attention immediately. See SDS below.
+This tool makes use of a heated solvent! A lab coat, face shield, and nitrile gloves must be wore by the user whenever the SCA 1200 HT is to be opened to protect from solution and vapor fumes. In case of contact with solution flush eyes, and skin with water, remove all contaminated clothing, and get medical attention immediately.
 ----
@@ Line 39: / Line 30: @@
   - Remove completed part on build tray from F270 3D printer
   - Remove part from build tray, making sure to scrape build tray free of ALL residue
-  - Dawn lab coat, nitrile gloves, and a face shield
+  - Put on a lab coat, nitrile gloves, and a face shield
   - Open lid on SCA 1200 HT
   - Slowly lift large basket, allow time to for excess solution to drip back into SCA 1200HT \\ NOTE: If solution rises above specific level alarm will sound, this is common when lifting or lowering basket and means you're moving too fast!
@@ Line 49: / Line 40: @@
   - Follow steps 3-6 to remove part, followed by steps 8 to replace basket
   - Part should be allowed to drip, before being rinsed in sink with plenty of warm water
 ----
-===== Reference Documentation =====
-{{:tools:scanaohbath:sca_1200ht_user_manual.pdf|}}
+===== Detailed Specifications =====
+  * Available Temperatures: 50, 60, 70, 85 degrees C
+  * Auto overfill alarm
+  * 46.3 L tank
-{{:tools:scanaohbath:msds-010-waterworks-concentrate-sds-400625-b-en-aghs-p400sc-wateworks-cleaning-solution.pdf|}}
 ----
-===== Training Documentation =====
+===== Reference Documentation =====
 [[f270_sop|FDM Training SOP]]
+{{:tools:scanaohbath:sca_1200ht_user_manual.pdf|}}
 ----