sandersop
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| sandersop [2022/07/14 19:26] – dave | sandersop [2022/07/14 20:20] (current) – [Overview] dave | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | =====CNSI Innovation Workshop Combination Sander User Outline===== | + | =====CNSI Innovation Workshop |
| - | This guide may be found online through the Innovation Workshop and Microfluidics wiki. | + | |
| ====Location==== | ====Location==== | ||
| The combination belt/disk sander is located in 2448 Elings Hall on the bench next to Fume Hood #3. | The combination belt/disk sander is located in 2448 Elings Hall on the bench next to Fume Hood #3. | ||
| Line 13: | Line 12: | ||
| ====Training==== | ====Training==== | ||
| Training is required before using the sander. | Training is required before using the sander. | ||
| + | ===Training Outline=== | ||
| + | - Explain parts of the tool | ||
| + | - Review safety concerns | ||
| + | - Demonstrate safe use of the tool | ||
| + | - Show location of supplies | ||
| + | - Demonstrate how to change belts/disks | ||
| + | - Cleanup | ||
| ====Overview==== | ====Overview==== | ||
| - | The grinder | + | The tool is a benchtop sander with a 1" wide x 42" long sanding belt, and an 8" disk sander driven by a common motor. Each of these sanders has a separate vacuum port connection. |
| ====User Guide==== | ====User Guide==== | ||
| **Sequence of operation: | **Sequence of operation: | ||
| Line 21: | Line 27: | ||
| - With workpiece resting on the table bring work into contact with the grinding wheel slowly and smoothly. | - With workpiece resting on the table bring work into contact with the grinding wheel slowly and smoothly. | ||
| - Move the work back and forth across the face of the sanding belt/disk to wear the abrasive evenly. | - Move the work back and forth across the face of the sanding belt/disk to wear the abrasive evenly. | ||
| - | - Use gentle pressure | + | - Use gentle pressure. Replace worn pads, or use a coarser sandpaper if more aggressive sanding is required. |
| - | - Remove workpiece, turn off grinder | + | - Turn off the sander. |
| - | - Use the shop vacuum to clean metal dust from work area. | + | - Use the shop vacuum to clean dust from work area. |
| ====Frequently Asked Questions==== | ====Frequently Asked Questions==== | ||
| * What materials can I sand? | * What materials can I sand? | ||
| Line 33: | Line 39: | ||
| * In the event of injury, contact lab staff and emergency services if necessary (?) | * In the event of injury, contact lab staff and emergency services if necessary (?) | ||
| ====Maintenance==== | ====Maintenance==== | ||
| - | * Use wire brushes to clear metal residue out of grinding wheel | + | * Change sandpaper as necessary |
| - | * Adjust grinding wheel guide as wheel wears | + | * Clean dust off of machine and work area |
| ====Supplies (In drawer labeled “Grinder Accessories”)==== | ====Supplies (In drawer labeled “Grinder Accessories”)==== | ||
| - | * 2 silicon carbide 8” grinding wheels | + | * 1" x 42" sanding belts |
| - | * 1 buffing wheel | + | * 8" adhesive-backed sanding disks |
| - | * Wire bristle brushes | + | ====Notes==== |
| - | * Grinding compounds | + | * Please refer to the manual for instructions on changing belts and sanding disks. |
sandersop.1657826780.txt.gz · Last modified: 2022/07/14 19:26 by dave