miicraft_50_sop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
miicraft_50_sop [2020/08/17 17:26] – [Accident Response] furst | miicraft_50_sop [2023/07/19 21:40] (current) – rylin | ||
---|---|---|---|
Line 11: | Line 11: | ||
In person training is required to use this machine. New users should read the Miicraft manual | In person training is required to use this machine. New users should read the Miicraft manual | ||
and follow along to the operating checklist (found on the IW GauchoSpace Website). | and follow along to the operating checklist (found on the IW GauchoSpace Website). | ||
- | Supplemental videos are also provided to follow along to | + | Supplemental videos are also provided to follow along to. |
**Training Outline** | **Training Outline** | ||
Description of the system: | Description of the system: | ||
- | * The system is comprised of the MiiCraft 3D printer, the connected desktop computer with the MiiUtility software, and the IPA bath and cleaning station in Fume Hood #4 a resin tank with a thin teflon bottom is placed over a glass projection window and clamped down to create a flat interface | + | * The system is comprised of the MiiCraft 3D printer, the connected desktop computer with the MiiUtility software, and the IPA bath and cleaning station in Fume Hood #4—a resin tank with a thin teflon bottom is placed over a glass projection window and clamped down to create a flat interface |
* A z-axis travelling build platform is lowered into the resin tank, where a fine layer of resin is cured through the teflon bottom using a DLP projector chip | * A z-axis travelling build platform is lowered into the resin tank, where a fine layer of resin is cured through the teflon bottom using a DLP projector chip | ||
* After printing, the entire build plate is removed and placed in the FormWash station, an agitated IPA bath that will clean off excess resin | * After printing, the entire build plate is removed and placed in the FormWash station, an agitated IPA bath that will clean off excess resin | ||
Line 32: | Line 32: | ||
- At the Printer: | - At the Printer: | ||
- Turn on the power if the printer is not already on | - Turn on the power if the printer is not already on | ||
- | - Retrieve a clean build plate from fume hood #4, clean off any excess resin with IPA | + | - Retrieve a clean build plate from Fume Hood #4, clean off any excess resin with IPA |
- | - Open the printer door and remove the resin tank cover visually inspect the resin. Stir it up gently with a card if any discolored oily streaks are present at the surface | + | - Open the printer door and remove the resin tank cover visually inspect the resin. Stir it up gently with a card if there are any discolored oily streaks are present at the surface |
- Install the clean build plate, make sure it is firmly seated, and press down on the locking lever Close the printer door and move on to the software. | - Install the clean build plate, make sure it is firmly seated, and press down on the locking lever Close the printer door and move on to the software. | ||
- At the Computer: | - At the Computer: | ||
Line 73: | Line 73: | ||
====Accident Response==== | ====Accident Response==== | ||
**Accident: | **Accident: | ||
- | print. | + | print. |
**Printer Response:** A mechanical error warning displays on screen. Printer is not responsive to | **Printer Response:** A mechanical error warning displays on screen. Printer is not responsive to | ||
- | computer commands and requires a hard reboot | + | computer commands and requires a hard reboot |
**Solution: | **Solution: | ||
- Press and hold power button for 2 seconds, then release. | - Press and hold power button for 2 seconds, then release. | ||
Line 82: | Line 82: | ||
- Remove obstructions and refresh computer connection in MiiController Window | - Remove obstructions and refresh computer connection in MiiController Window | ||
- | **Accident: | + | **Accident: |
- | **Printer Response:** Print Quality is poor // | + | **Printer Response:** Print Quality is poor \\ |
**Solution: | **Solution: | ||
- Replace build tank | - Replace build tank | ||
- | **Accident: | + | **Accident: |
- | **Printer Response:** New prints will not start, build platform stand immersed in resin. | + | **Printer Response:** New prints will not start, build platform stand immersed in resin. |
**Solution: | **Solution: | ||
- | **Accident: | + | **Accident: |
**Solution: | **Solution: | ||
+ | |||
+ | ====References==== | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | {{ : | ||
+ | |||
miicraft_50_sop.1597685200.txt.gz · Last modified: 2020/08/17 17:26 by furst