Microfluidics Lab and Innovation Workshop Wiki

User Tools

Site Tools

Trace:
laser_cutter_training_sop

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
laser_cutter_training_sop [2023/07/17 22:55] – rylinlaser_cutter_training_sop [2023/09/12 22:00] – [Material] bdincau
Line 1: Line 1:
 =====CNSI Innovation Workshop and Microfluidics Lab Trotec Speedy100 ​Safe Operating Procedures=====  =====CNSI Innovation Workshop and Microfluidics Lab Trotec Speedy100 ​Safe Operating Procedures===== 
-Last Updated: 5/31/23 Haley \\+Last Updated: 7/17/23 Rachel \\
 This SOP is compiled from the following sources. For more information reference these sources. This SOP is compiled from the following sources. For more information reference these sources.
   * [[https://www.troteclaser.com/fileadmin/content/images/Contact_Support/Manuals/8010-Speedy-100-Manual-EN.pdf|Trotec Speedy Manual]]   * [[https://www.troteclaser.com/fileadmin/content/images/Contact_Support/Manuals/8010-Speedy-100-Manual-EN.pdf|Trotec Speedy Manual]]
Line 61: Line 61:
   * ABS (acrylonitrile butadiene styrene)   * ABS (acrylonitrile butadiene styrene)
   * Acrylic (also known as Plexiglas, Lucite, PMMA)   * Acrylic (also known as Plexiglas, Lucite, PMMA)
-  * Delrin (POM, acetal) — for a supplier, try www.mcmaster.com.+  * Delrin (POM, acetal) — for a supplier, try www.mcmaster.com. **Must use nitrogen assist when cutting delrin**
   * Kapton tape (Polyimide)   * Kapton tape (Polyimide)
   * Mylar (polyester)   * Mylar (polyester)
Line 165: Line 165:
 |} |}
  
-====Functional Engraving Recipes==== +====General Kerf Width For Acrylic====
-For users looking to cut acrylic at different depths, different cut depths were tested with different power settings. +
- +
-{| style="" +
-|+  +
-! +
-Engraving Settings +
-! +
-Engraving Cut Thickness +
-|- +
-| +
-0 mm +
-| +
-0% power, 0% speed +
-|- +
-| +
-0.208 mm +
-| +
-50% power, 30% speed +
-|- +
-| +
-0.314 mm +
-| +
-60% power, 30% speed +
-|- +
-| +
-0.352 mm +
-| +
-70% power, 30% speed +
-|- +
-| +
-0.413 mm +
-| +
-80% power, 30% speed +
-|- +
-| +
-0.446 mm +
-| +
-90% power, 30% speed +
-|- +
-| +
-0.485 mm +
-| +
-100% power, 30% speed +
-|} +
- +
-====General Curf Width For Acrylic====+
 {| style="" {| style=""
 |+ |+
Line 217: Line 171:
 Thickness Thickness
 ! !
-Curf Width+Kerf Width
 |- |-
 | |
laser_cutter_training_sop.txt · Last modified: 2023/09/12 22:01 by bdincau