f270_sop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
f270_sop [2020/08/27 16:39] – [Ultimaker 3 Quick Review] furst | f270_sop [2022/07/01 17:13] (current) – [Part Removal and Cleaning] haley | ||
---|---|---|---|
Line 94: | Line 94: | ||
* If support was used, submerge print in warm water for several hours to dissolve PVA filament. (prints can warp if submerged in water for over 24 hours) \\ | * If support was used, submerge print in warm water for several hours to dissolve PVA filament. (prints can warp if submerged in water for over 24 hours) \\ | ||
**F270** | **F270** | ||
- | * Don gloves, face shield, and lab coat | + | * Remove the build tray and flex it to break the bond between the material and the tray. |
- | * Carefully, slowly and without splashing cleaning solution open the support removal tank lid, remove and open the tank | + | * Separate your part from the build tray with a spatula and scrape off any debris so they tray can be reused. |
+ | * Put on the appropriate PPE: don gloves, | ||
+ | * Carefully, slowly, and without splashing cleaning solution, open the support removal tank lid and remove and open the tank. | ||
* Place large parts directly in the tank, small parts may be put in the SS box and placed into the main basket. | * Place large parts directly in the tank, small parts may be put in the SS box and placed into the main basket. | ||
- | * Carefully, slowly and without splashing lower the basket back into the tank and close the lid. | + | * Carefully, slowly, and without splashing lower the basket back into the tank and close the lid. |
- | * Set timer for 6 hours setting | + | * Set timer for 8 hours using the " |
- | * After cleaning time has elapsed follow the instructions above for opening and removing parts. | + | * Select |
- | * Rinse part in warm water | + | * After cleaning time has elapsed, follow the instructions above for opening and removing parts. |
+ | * Rinse part in warm water. | ||
---- | ---- | ||
Line 128: | Line 131: | ||
====Safety Concerns==== | ====Safety Concerns==== | ||
* Both print heads and bed are heated during operation. Do not attempt to clean, remove, or adjust without allowing for adequate cool down time. | * Both print heads and bed are heated during operation. Do not attempt to clean, remove, or adjust without allowing for adequate cool down time. | ||
- | * Keep hands clear of printer during operation. Pause print before clearing or adjusting | + | * Keep hands clear of printer during operation. Pause print before clearing or adjusting |
| | ||
Line 142: | Line 145: | ||
====Post Processing==== | ====Post Processing==== | ||
- | * If support was constructed from ABS carefully break away with pliers | + | * If support was constructed from dissoluble filament clean using the F270 Support Removal Apparatus which is filled |
- | * If support | + | * Build tray should be scraped clean and free of any support |
- | ====Maintenance==== | + | ====Maintenance |
- | * Bed should be cleaned with IPA between prints | + | * Clean oven chamber weekly |
- | * Print heads and silicone head protector should be cleaned as needed | + | * Clean platen weekly |
- | * Filament should be dried before use if printer has been idle for several weeks | + | * Inspect, wipe, and clean tip wipe assemblies monthly |
- | * Bed leveling should be completed every time print cores are swapped | + | * Clean exterior of printer as needed |
- | * Print cores should be swapped | + | * Clean touchscreen as needed |
----- | ----- | ||
f270_sop.1598546366.txt.gz · Last modified: 2020/08/27 16:39 by furst