Differences

This shows you the differences between two versions of the page.

--- einscantrainginsop [2020/09/04 17:59] – furst
+++ einscantrainginsop [2023/01/06 01:08] (current) – [EinScan-SP Training SOP] haley
@@ Line 2: / Line 2: @@
 Last edited: Furst (8/28/20)
-Instructor:
-Date:
-{| style=""
-|+ Attendees:
-!
-!
-Name
-!
-Group or Company
-!
-Signature
-|-
-|1
-|
-|
-|
-|-
-|2
-|
-|
-|
-|-
-|3
-|
-|
-|
-|-
-|4
-|
-|
-|
-|-
-|5
-|
-|
-|
-|-
-|6
-|
-|
-|
-|}
------
 ====Overview:====
@@ Line 232: / Line 185: @@
 ====Safe Operation Procedures Review====
-  - Check resin cartridge and tank, make sure build material matches and is desired material.
+  - Create a new project and designate file location
-  - If resin is not desired material, disconnect wiper at build tank, remove build plate by sliding towards front of fume hood. Remove cartridge, cap valve on bottom and close valve on top of cartridge. Replace build tank, wiper, and cartridge with desired material.
+  - Select desired texture mode (texture uses color data whereas non texture takes less time)
-  - Launch Preform on Ultimaker computer
+  - Adjust brightness slider to properly expose image
-  - Import desired STL
+  - Select desired scanning mode (turntable or tripod are standard)
-  - Select "one click print" in the top left corner menu, change position, orientation, resolution and support as desired (note: that Preform will report on print ability of model, changing part rotation can affect print ability.
+  - Start Scan
-  - Select print (orange button) from top left menu
+  - After scan completion using shift + left click to remove extraneous data
-  - Select desired printer
+  - Correct any misalignment using the align and shift + left click to select coincident points
-  - Press button on Formlabs printer to start print
+====Post Processing and exporting====
+  - Select mesh to convert to mesh body
-====Post Processing====
+  - Select watertight to create closed object or unwatertight to edit object file
-  - Excess resin should be removed from the build tray and part with IPA over a waste container.
+  - Select desired simplification ratio (to reduce processor stress) and file type (.STL, .OBJ, .PLY, .3MF, or .ASC)
-  - Place build tray and part in the Form Wash for 20 to 30 minuets (part can be placed individually within basket if necessary
-  - Allow 30 minuets for IPA to evaporate before placing part in Form Cure
-  - Set Form Cure time and temperature based on resin type, place part within form cure, wait for time to elapse
 ====Maintenance====
-  * Switching resin types
+  * Calibration should take place once a week or before a scan for optimal accuracy
-    * Close breather valve on resin cartridge
+  * Scanner and turntable should be wiped down frequently
-    * Resin cartridge by pulling straight up on the handle behind the form labs printers
+  * Computer should be restarted periodically and plugged in
-    * Cap the cartridge valve using the included orange tap and cap
-    * Remove the wiper by pulling straight out towards the front of the fume hood.
-    * Pull the resin tray out of the printer by pulling firmly straight out toward you
-    * Lift the wiper and resin tray out simultaneously, and carefully place on resin shelf within fume hood.
-    * Cover resin tray with black plastic cover and label
-    * Replace resin tray with clean or desired resin tank. Push tank and wiper firmly back toward the Form 2 until it clicks into place
-    * Replace resin cartridge and open valve