einscantrainginsop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
einscantrainginsop [2020/09/01 18:07] – furst | einscantrainginsop [2023/01/06 01:08] (current) – [EinScan-SP Training SOP] haley | ||
---|---|---|---|
Line 2: | Line 2: | ||
Last edited: Furst (8/28/20) | Last edited: Furst (8/28/20) | ||
- | Instructor: | ||
- | |||
- | Date: | ||
- | |||
- | {| style="" | ||
- | |+ Attendees: | ||
- | ! | ||
- | |||
- | ! | ||
- | Name | ||
- | ! | ||
- | Group or Company | ||
- | ! | ||
- | Signature | ||
- | |- | ||
- | |1 | ||
- | | | ||
- | | | ||
- | | | ||
- | |- | ||
- | |2 | ||
- | | | ||
- | | | ||
- | | | ||
- | |- | ||
- | |3 | ||
- | | | ||
- | | | ||
- | | | ||
- | |- | ||
- | |4 | ||
- | | | ||
- | | | ||
- | | | ||
- | |- | ||
- | |5 | ||
- | | | ||
- | | | ||
- | | | ||
- | |- | ||
- | |6 | ||
- | | | ||
- | | | ||
- | | | ||
- | |} | ||
- | |||
- | ----- | ||
====Overview: | ====Overview: | ||
Line 99: | Line 52: | ||
====Safe Operation of this Tool==== | ====Safe Operation of this Tool==== | ||
**Before Using the Scanner:** | **Before Using the Scanner:** | ||
+ | |||
Make sure that the object: | Make sure that the object: | ||
* Is larger than 30x30x30mm (1.2x1.2x1.2in) | * Is larger than 30x30x30mm (1.2x1.2x1.2in) | ||
Line 114: | Line 68: | ||
- Adjust __Brightness slider__ {{: | - Adjust __Brightness slider__ {{: | ||
- | **Scanning With the Turntable: | + | **Scanning With the Turntable: |
{{: | {{: | ||
- Check the __Use Turntable__ box and specify the number of increments (8-180 steps). The __Align Mode__ menu will appear. | - Check the __Use Turntable__ box and specify the number of increments (8-180 steps). The __Align Mode__ menu will appear. | ||
Line 221: | Line 175: | ||
Remove the calibration board from the stand and place in the protective drawstring bag. Remove the stand from the turntable and proceed with scanning. | Remove the calibration board from the stand and place in the protective drawstring bag. Remove the stand from the turntable and proceed with scanning. | ||
- | + | ----- | |
+ | |||
+ | | ||
+ | Tool Lead: \\ | ||
+ | Contact: andrewfurst@ucsb.edu | ||
+ | ====Safety Concern==== | ||
+ | * Lab coat and gloves must me used when handling resin | ||
+ | * Anything with uncured resin must be transported within a container to avoid spilling | ||
+ | |||
+ | ====Safe Operation Procedures Review==== | ||
+ | - Create a new project and designate file location | ||
+ | - Select desired texture mode (texture uses color data whereas non texture takes less time) | ||
+ | - Adjust brightness slider to properly expose image | ||
+ | - Select desired scanning mode (turntable or tripod are standard) | ||
+ | - Start Scan | ||
+ | - After scan completion using shift + left click to remove extraneous data | ||
+ | - Correct any misalignment using the align and shift + left click to select coincident points | ||
+ | ====Post Processing and exporting==== | ||
+ | - Select mesh to convert to mesh body | ||
+ | - Select watertight to create closed object or unwatertight to edit object file | ||
+ | - Select desired simplification ratio (to reduce processor stress) and file type (.STL, .OBJ, .PLY, .3MF, or .ASC) | ||
+ | |||
+ | ====Maintenance==== | ||
+ | * Calibration should take place once a week or before a scan for optimal accuracy | ||
+ | * Scanner and turntable should be wiped down frequently | ||
+ | * Computer should be restarted periodically and plugged in | ||
einscantrainginsop.1598983627.txt.gz · Last modified: 2020/09/01 18:07 by furst