Differences

This shows you the differences between two versions of the page.

--- einscantrainginsop [2020/08/19 19:41] – furst
+++ einscantrainginsop [2023/01/06 01:08] (current) – [EinScan-SP Training SOP] haley
@@ Line 1: / Line 1: @@
 =====EinScan-SP Training SOP=====
-====Tool Name and Location====
+Last edited: Furst (8/28/20)
-The SHINING3D EinScan-SP 3D Scanner is located in Fume Hood #1 in Elings 2448.
+====Overview:====
+This training provides an introduction to using the EinScan including:
+  * Setting up and calibrating the scanner
+  * Optimal conditions and techniques for scanning particulate parts
+  * Using the EinScan Turntable
+  * Fixing/reducing STL mesh files for export
+====Location:====
+the EinScan is located in fume hood #1 in the Innovations Workshop
 ====Safety====
 **Machine Limitations:**
   * The turntable has a maximum weight limit of 5kg (~11lbs). Exceeding this weight could damage the machine and its internal components.
-**Environmental:**'
+**Environmental:**
   * Keep the scanner in a well ventilated area. Keep flammables, corrosive agents, and liquids away from the scanner. Failing to do so will damage the machine and its internal components.
 **Physical:**
   * The projector emits a bright light. Avoid looking directly into the light source to prevent eye injury.
 ====Training====
-**training requirements:**
+**Training requirements:**
 Users must attend the in-person training session and should consult the Safe Operating Procedure and EinScan-SP Manual (both found on the Innovation Workshop GauchoSpace page).
 **Training Outline**
   - Overview of the scanner and the system setup
@@ Line 40: / Line 52: @@
 ====Safe Operation of this Tool====
 **Before Using the Scanner:**
 Make sure that the object:
   * Is larger than 30x30x30mm (1.2x1.2x1.2in)
@@ Line 55: / Line 68: @@
   - Adjust __Brightness slider__ {{:tools:einscan-sp:brightness.jpg?35|}}until no red areas are visible on the desired part
-**Scanning With the Turntable:**
+**Scanning With the Turntable:** \\
 {{:tools:einscan-sp:turntable_menu.jpg?200|}}
   - Check the __Use Turntable__ box and specify the number of increments (8-180 steps). The __Align Mode__ menu will appear.
@@ Line 126: / Line 139: @@
 -----
-====Accident Response:====
 ====References====
 **Manuals:**
@@ Line 163: / Line 175: @@
 Remove the calibration board from the stand and place in the protective drawstring bag. Remove the stand from the turntable and proceed with scanning.
+-----
+ ====Einscan Quick Review====
+Tool Lead:    \\
+Contact: andrewfurst@ucsb.edu      \\
+====Safety Concern====
+  * Lab coat and gloves must me used when handling resin
+  * Anything with uncured resin must be transported within a container to avoid spilling
+====Safe Operation Procedures Review====
+  - Create a new project and designate file location
+  - Select desired texture mode (texture uses color data whereas non texture takes less time)
+  - Adjust brightness slider to properly expose image
+  - Select desired scanning mode (turntable or tripod are standard)
+  - Start Scan
+  - After scan completion using shift + left click to remove extraneous data
+  - Correct any misalignment using the align and shift + left click to select coincident points
+====Post Processing and exporting====
+  - Select mesh to convert to mesh body
+  - Select watertight to create closed object or unwatertight to edit object file
+  - Select desired simplification ratio (to reduce processor stress) and file type (.STL, .OBJ, .PLY, .3MF, or .ASC)
+====Maintenance====
+  * Calibration should take place once a week or before a scan for optimal accuracy
+  * Scanner and turntable should be wiped down frequently
+  * Computer should be restarted periodically and plugged in