carbide_3d_nomad_883_training_sop
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
carbide_3d_nomad_883_training_sop [2020/09/08 19:53] – furst | carbide_3d_nomad_883_training_sop [2020/09/08 20:12] – furst | ||
---|---|---|---|
Line 90: | Line 90: | ||
- Cutting/ | - Cutting/ | ||
- Typically selecting machining geometry will set many of the heights automatically, | - Typically selecting machining geometry will set many of the heights automatically, | ||
- | - Machining passes | + | - Machining passes |
- | {{: | + | |
- Part of feeds and speeds, HSM Works will auto fill many of the boxes, however due to the limited power and rigidity of the machine, stepdowns should be reduced based on the reference material and " | - Part of feeds and speeds, HSM Works will auto fill many of the boxes, however due to the limited power and rigidity of the machine, stepdowns should be reduced based on the reference material and " | ||
- " | - " | ||
Line 133: | Line 132: | ||
====Choosing tools==== | ====Choosing tools==== | ||
Many tools are optimized for different materials, and although a 2 flute endmill can do most operations, it is not always ideal. Single and duel high helix endmills are available for plastics, woods, and composits, with carbide endmills and burs available for abrasive materials such as glass fiber reinforced materials such as circuit boards. | Many tools are optimized for different materials, and although a 2 flute endmill can do most operations, it is not always ideal. Single and duel high helix endmills are available for plastics, woods, and composits, with carbide endmills and burs available for abrasive materials such as glass fiber reinforced materials such as circuit boards. | ||
- | feeds and speeds can be found {{: | + | Feeds and speeds can be found {{: |
====File Types==== | ====File Types==== | ||
Line 146: | Line 145: | ||
* The acrylic shield must be in place and lowered before starting a job | * The acrylic shield must be in place and lowered before starting a job | ||
* The spindle must be completely stopped before adjusting or removing work piece | * The spindle must be completely stopped before adjusting or removing work piece | ||
- | * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper ====Safe Operating Procedures Review==== | + | * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper |
- | - Launch Cura version 4 (blue icon) | + | ====Safe Operating Procedures Review==== |
- | - From connected printers, select IW-Ultimaker3 | + | - Design part using Solidworks or other CAD platform |
- | - Select File -> Open Files -> Open desired project (.STL file type) | + | - Using HSM Works or Carbide Create generate tool paths |
- | - Using task bar on the left hand side, position model as desired | + | |
- | - From print settings, select slice height, infill percentage, | + | - Use 2D and 3D clearing and pocketing to remove the bulk of the material while using "stock to leave" to allow for a finishing pass |
- | - Support can be generated using ether nozzle, typically nozzle one holds build material with nozzle two printing with dissolvable support material. | + | - Simulate the toolpaths to verify that the tool will not crash and is cutting in the desired |
- | - Setting can be fined tuned using the "Custom" | + | - Using the 17 and 11 mm wrenches loosen the collet nut to change out the tool or collet itself if switching shank diameter |
- | - Within custom settings, nozzle and build plate temps can be adjusted (build plate temps should be based off of build material) | + | - Home the machine and zero the tool using Carbide Motion under the "jog" |
- | | + | - Upload the G-Code into Carbide Motion under " |
- | - Connect thumb drive to printer -> select desired file -> select print\\ | + | - Start program |
- | Note: Adjusting settings may lead to more (OR LESS) successful prints. Contact Workshop Wizard responsible for Ultimaker if print fails or knowledge of advanced settings is desired. | + | |
====Post Processing==== | ====Post Processing==== | ||
- | * If support was constructed from ABS carefully break away with pliers | + | * Use a file to debur the part |
- | | + | |
====Maintenance==== | ====Maintenance==== | ||
- | * Bed should be cleaned with IPA between prints | + | * Tools should be wiped clear of chips or coolant using an acid brush |
- | * Print heads and silicone head protector | + | * The router |
- | * Filament | + | * Once a month the router |
- | * Bed leveling | + | * Twice a year the router |
- | * Print cores should be swapped | + | |
----- | ----- | ||
carbide_3d_nomad_883_training_sop.txt · Last modified: 2020/09/13 21:47 by furst