Differences

This shows you the differences between two versions of the page.

--- x1carbon_sop [2024/08/19 17:48] – [Additional Information] kho
+++ x1carbon_sop [2024/08/30 17:54] (current) – kho
@@ Line 5: / Line 5: @@
   *Safety: hot printheads & bed, moving components
   *Job Setup:
-    *At the computer: CAD -> export .stl -> Bambu Studio OR OrcaSlicer (print parameters, support materials) -> select "Innovation Workshop X1C" printer -> start print (make sure "Enable AMS" and "Bed Leveling" are selected)-> record in FBS
+    *At the computer: CAD -> export .stl -> Bambu Studio OR OrcaSlicer (set upp print parameters and support materials) -> select "Innovation Workshop X1C" printer -> start print (make sure "Enable AMS" and "Bed Leveling" are selected)-> record in FBS
-    *At the printer: remove leftover supports/calibration lines -> clean build tray
+    *At the printer: remove leftover supports/calibration lines -> clean and dry build tray
 ====Safety Concerns====
@@ Line 14: / Line 14: @@
  ====Common Mistakes====
-  *Inadequate part adhesion to the bed - can cause print failure or breakage of entire print head assembly
+  *Inadequate part adhesion to the bed - can cause print failure
-    *Can be prevented with proper bed cleaning, use of hairspray, bed adhesion print settings, and high enough printing temperature
+    *Can be prevented with proper bed cleaning, bed adhesion print settings, and correct build tray alignment
  ====Safe Operating Procedures Review====
@@ Line 37: / Line 37: @@
 ====Maintenance====
   * Scrape off calibration lines on the sides of the build tray
-  * Bed should be cleaned with soap and water in the sink
+  * Bed should be cleaned with soap and water and can be dried using paper towels
+     * **DO NOT** touch the surface of build tray with your bare hands. Hold build tray by the tabs
-====Bambu Labs Software Information====
+====Bambu Studio Software Information====
-  -    //Auto Orient//: Gives you the recommended orientation for your print. Usually is the best orientation, but you should still think about specific qualities of your print and limitations of the printer.
+{{:bambuprintersettings.jpg?600}}
+  - Select the correct nozzle that you are using. (Typically, the 0.4 nozzle is the one in the printer)
+  - Make sure the "Textured PEI Plate" is selected
+{{:bambuprintersettings2.jpg?600}}
+  -    //Auto Orient//: Gives you the recommended orientation for your print. Usually is the best orientation, but you should still think about specific dimensions and features of your print and the limitations of the printer.
   -    //Arrange//: Arranges your models near the center of the build tray
-  -    //Rotation//: Allows you to rotate your model. Make sure to select the face that you want to align to the print bed. Ensure that you align the face with the **greatest surface area.**
+  -    //Move//: Allows you to move your model with a relative coordinate system
-  -    //Mirror//: Allows you to mirror your model.
+  -    //Rotate//: Allows you to rotate your model in 3 dimensions to get the right orientation for your print. You can either make rotations dragging around the arrows or by changing the coordinates.
-  -    //Per Model Settings//: Allows you to change print settings for each model. This allows you to have multiple prints on the same build plate while still using different print settings for each model.
+  -    //Scale//: Allows you to scale your model to size. (units are in mm)
-  -    //Support Blocker//: Allows you to prevent support from being generated in certain areas.
-  -    //Print selected model with Extruder 1//: Select which model to print with Extruder 1. This is generally build material.
-  -    //Print selected model with Extruder 2//: Select which model to print with Extruder 2. This is generally support material.
-{{:print_settings.png?600|}}
-**Cura Print Settings**
-  -   //Printer Type//: Choose Ultimaker 3 or Ultimaker 5 Extended.
-  -   //Material Type//: This allows you to choose the material type you have loaded into the printer. Ensure that both the material type as well as the printhead diameter settings match the printheads on the printer
-  -   //Layer thickness, infill, support//: Allows you to adjust the thickness, infill, and support you wish to use. **Ensure that you enable adhesion**