Differences

This shows you the differences between two versions of the page.

--- wen_drill_press [2022/08/26 22:08] – [Operating Procedures] haley
+++ wen_drill_press [2024/09/26 19:43] (current) – epace
@@ Line 1: / Line 1: @@
 ====== WEN vertical Drill Press ======
-^                           WEN vertical Drill Press                               ^
+^                           Drill Press                               ^
 |          {{:tools:wen_drill_press:wen_drill_press.jpg?200|}}           |
-| **Tool Type:**                  "Vertical Milling Machine"                   |
+| **Tool Type:**                  Drill press                   |
-| **Location:**                   "Innovations Workshop"                   |
+| **Location:**                   Elings 2442                   |
-|  **Supervisor**        |  **Tool Lead**  |
+| **Description:**                Vertical manual drill press                           |
-|  David Bothman         |  "WW Name"  |
+| **Manufacturer:**               WEN                           |
-|  (805) 893-4125        |  (###) ###-####  |
-|  bothman@cnsi.ucsb.edu  |  "WW Email"  |
-| **Description:**                "Drill Press"                           |
-| **Manufacturer:**               "WEN"                           |
 ----
@@ Line 19: / Line 14: @@
 ===== About =====
 This vertical drill press is one of the largest upright tools in the Innovations Workshop. It has a speed control lever on the left side of the head, and a vertical quill feed on the right. The chuck key is located on the right side of the head and should be replaced after use to avoid mixing chuck keys.
-----
-===== Detailed Specifications =====
-  * Spindle Speed Range: 280-3,100 RPM (740-3,100 on main pulley)
-  * Quill extension length: 4 3/8"
-  * Max Drill Bit Diameter:16 mm
-  * Max Work piece Height: 44"
 ----
@@ Line 33: / Line 19: @@
 ===== Safety Concerns =====
-  * Safety glasses, close toe shoes, and long pants must be warn when operating the machine
+  * Safety glasses, closed toe shoes, and long pants must be warn when operating the machine
   * Metal chips can be incredibly sharp, do not touch any chips directly instead using an acid brush to remove chips
   * Do not inhale any fumes resulting from drilling using oil
@@ Line 41: / Line 27: @@
 ----
-===== Operating Procedures =====
+===== Training Documentation =====
-  - Layout and center punch the holes you wish to drill
-  - Collect all necessary tools for your drilling operation.
+[[Drill Press SOP]]
-  - Insert the bit into the drill chuck, tighten with the chuck key, and remove the chuck key before continuing.
-  - Align the holes with the drill bit and secure the part using the vice or the drill bed clamp.
-  - Adjust the work table to the appropriate height and lock securely.
-  - Check that the tool can spin freely and that it is clear of the part.
-  - Adjust feed rate
-  - Apply cutting lubricant to the part.
-  - Turn the machine on (Do not leave running unattended).
-  - Use peck drilling operations to drill the hole, remove material in 0.05 inch increments.
-  - Remove chips and swarf using a brush.
-  - Power down the machine when done.
-  - Use a brush and/or rag to clean up any chips, shavings, and oil from the drill press and the surrounding areas.
-  - Return all tools to their proper location and power down the drill press.Tidy up the work area.
 ----
+===== Detailed Specifications =====
+  * Spindle Speed Range: 280-3,100 RPM (740-3,100 on main pulley)
+  * Quill extension length: 4 3/8"
+  * Max Drill Bit Diameter:16 mm
+  * Max Work piece Height: 44"
+----
 ===== Reference Documentation =====
@@ Line 67: / Line 51: @@
-===== Training Documentation =====
-[[Drill Press SOP]]
-----