weekly_cleaning
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| weekly_cleaning [2024/09/24 19:29] – epace | weekly_cleaning [2024/09/26 19:24] (current) – [2442 Maintenance & Cleaning Manual] epace | ||
|---|---|---|---|
| Line 3: | Line 3: | ||
| View the retired cleaning manual: [[Workshop Wizard Handbook|Weekly Cleaning Guide]] | View the retired cleaning manual: [[Workshop Wizard Handbook|Weekly Cleaning Guide]] | ||
| - | ==== Microfluidics | + | ==== Elings 3430 Lab Maintenance & Cleaning Manual ==== |
| 1. Check and replenish paper towels in dispensers | 1. Check and replenish paper towels in dispensers | ||
| Line 48: | Line 48: | ||
| * Place in hazardous waste bin. | * Place in hazardous waste bin. | ||
| * Replace bag with new bag located on metal shelves near entrance. | * Replace bag with new bag located on metal shelves near entrance. | ||
| + | |||
| 14. Take all resin trays and cartridges out of the resin printers and put them back in the cabinet below. | 14. Take all resin trays and cartridges out of the resin printers and put them back in the cabinet below. | ||
| + | |||
| 15. Fill resin wash with IPA in between the marked lines. Measure the specific gravity of the IPA in the wash. | 15. Fill resin wash with IPA in between the marked lines. Measure the specific gravity of the IPA in the wash. | ||
| * If the O-ring on the measuring device sits above the large flaps, replace the IPA. | * If the O-ring on the measuring device sits above the large flaps, replace the IPA. | ||
| * Reminder: Check the IPA level in the squirt bottles regularly. | * Reminder: Check the IPA level in the squirt bottles regularly. | ||
| + | |||
| + | |||
| 16. Refill CNC drill squirt bottle. | 16. Refill CNC drill squirt bottle. | ||
| * Use blue coolant. | * Use blue coolant. | ||
| * Check the level in the jug and refill if necessary. | * Check the level in the jug and refill if necessary. | ||
| - | * Undiluted coolant is underneath the sink. Mix the cool according to the ratio written on the bottle | + | * Undiluted coolant is underneath the sink. Mix the cool according to the ratio written on the bottle. |
| + | |||
| 17. Make sure all cabinets are locked and lockboxes are locked and closed. | 17. Make sure all cabinets are locked and lockboxes are locked and closed. | ||
| + | |||
| 18. Turn off Keyence light, put black stage on, make sure 200x objective is in use. | 18. Turn off Keyence light, put black stage on, make sure 200x objective is in use. | ||
| + | |||
| 19. Clean the laser cutter. | 19. Clean the laser cutter. | ||
| * Take out the (layer with a bunch of hexagons) and vacuum small bits from the bottom. | * Take out the (layer with a bunch of hexagons) and vacuum small bits from the bottom. | ||
| + | |||
| + | |||
| 20. Clean laser cutter lens. | 20. Clean laser cutter lens. | ||
| * Tools in the laser cutter cabinet. | * Tools in the laser cutter cabinet. | ||
| Line 68: | Line 78: | ||
| * **NOTE**: The convex side of the lens will have a more prominent (relative to the concave side) dot in the center. | * **NOTE**: The convex side of the lens will have a more prominent (relative to the concave side) dot in the center. | ||
| * The grey knob on the laser will release the mirror for cleaning if necessary. | * The grey knob on the laser will release the mirror for cleaning if necessary. | ||
| + | |||
| + | |||
| 21. Ultimaker cleaning & Bambu cleaning | 21. Ultimaker cleaning & Bambu cleaning | ||
| * Clean out any scrap filament from the bottom of both printers. | * Clean out any scrap filament from the bottom of both printers. | ||
| * Make sure to wipe remaining glue on the Ultimaker platform by taking out the platform and using IPA. | * Make sure to wipe remaining glue on the Ultimaker platform by taking out the platform and using IPA. | ||
| - | * Clean the Bambu tray by removing and washing with warm water and soap | + | * Clean the Bambu tray by removing and washing with warm water and soap. |
| + | |||
| 22. Stratasys maintenance | 22. Stratasys maintenance | ||
| * Check the filament level, replace it with stock from the shelves in the corridor if necessary. | * Check the filament level, replace it with stock from the shelves in the corridor if necessary. | ||
| * To vacuum the print platform, go to settings and bring the gantry up; preferably use gloves. | * To vacuum the print platform, go to settings and bring the gantry up; preferably use gloves. | ||
| + | |||
| + | |||
| 23. SCA 1200HT maintenance | 23. SCA 1200HT maintenance | ||
| * Check for the fluid threshold level weekly. Over longer intervals, remove the container to check for parts in the cleaner (rotate 90 degrees to minimize splashing.) | * Check for the fluid threshold level weekly. Over longer intervals, remove the container to check for parts in the cleaner (rotate 90 degrees to minimize splashing.) | ||
| * **Note**: This device is particularly dangerous. Wear gloves, coat, and face shield when opening the door. Ask the manager or other WWs for detailed instructions. | * **Note**: This device is particularly dangerous. Wear gloves, coat, and face shield when opening the door. Ask the manager or other WWs for detailed instructions. | ||
| * **Note**: The alarm may sound if the container is lowered too quickly. Silence the alarm with the button that is indicated with a warning light but do so only if you are certain that this was the cause of the alarm. | * **Note**: The alarm may sound if the container is lowered too quickly. Silence the alarm with the button that is indicated with a warning light but do so only if you are certain that this was the cause of the alarm. | ||
| + | |||
| + | |||
| 24. Sweep and mop | 24. Sweep and mop | ||
| * Walkways and under benches. | * Walkways and under benches. | ||
| Line 86: | Line 104: | ||
| * **Rule of thumb**: Best to do in the mornings or weekends to avoid congestion in the lab. | * **Rule of thumb**: Best to do in the mornings or weekends to avoid congestion in the lab. | ||
| -------- | -------- | ||
| - | ==== Innovation Workshop | + | ==== 2442 Maintenance & Cleaning Manual ==== |
| 1. Check and replenish paper towels | 1. Check and replenish paper towels | ||
| * There are paper towel dispensers above every sink. | * There are paper towel dispensers above every sink. | ||
| - | * Extra paper towels can be found in uFl. | + | * Extra paper towels can be found in 3430. |
| 2. Check and replenish gloves | 2. Check and replenish gloves | ||
| - | * Extra boxes are located in uFl. | + | * Extra boxes are located in 3430. |
| 3. Replenish hazardous waste labels | 3. Replenish hazardous waste labels | ||
| * Empty solvent bottles should not be rinsed. Make sure to cross out the labels with a Sharpie and have a waste solvent label pre-tagged. | * Empty solvent bottles should not be rinsed. Make sure to cross out the labels with a Sharpie and have a waste solvent label pre-tagged. | ||
weekly_cleaning.1727206198.txt.gz · Last modified: 2024/09/24 19:29 by epace