weekly_cleaning
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| weekly_cleaning [2024/09/23 21:14] – created epace | weekly_cleaning [2024/09/26 19:24] (current) – [2442 Maintenance & Cleaning Manual] epace | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Workshop Wizard Weekly Cleaning and Maintenance ===== | ===== Workshop Wizard Weekly Cleaning and Maintenance ===== | ||
| - | ==== Microfluidics | + | View the retired cleaning manual: [[Workshop Wizard Handbook|Weekly Cleaning Guide]] |
| + | |||
| + | ==== Elings 3430 Lab Maintenance & Cleaning Manual ==== | ||
| 1. Check and replenish paper towels in dispensers | 1. Check and replenish paper towels in dispensers | ||
| Line 46: | Line 48: | ||
| * Place in hazardous waste bin. | * Place in hazardous waste bin. | ||
| * Replace bag with new bag located on metal shelves near entrance. | * Replace bag with new bag located on metal shelves near entrance. | ||
| - | 14. Take all resin trays and cartridges out of the resin printers and put them back in the cabinet below | + | |
| + | 14. Take all resin trays and cartridges out of the resin printers and put them back in the cabinet below. | ||
| 15. Fill resin wash with IPA in between the marked lines. Measure the specific gravity of the IPA in the wash. | 15. Fill resin wash with IPA in between the marked lines. Measure the specific gravity of the IPA in the wash. | ||
| * If the O-ring on the measuring device sits above the large flaps, replace the IPA. | * If the O-ring on the measuring device sits above the large flaps, replace the IPA. | ||
| * Reminder: Check the IPA level in the squirt bottles regularly. | * Reminder: Check the IPA level in the squirt bottles regularly. | ||
| - | 16. Refill CNC drill squirt bottle | + | |
| + | |||
| + | 16. Refill CNC drill squirt bottle. | ||
| * Use blue coolant. | * Use blue coolant. | ||
| * Check the level in the jug and refill if necessary. | * Check the level in the jug and refill if necessary. | ||
| - | * Undiluted coolant is underneath the sink. Mix the cool according to the ratio written on the bottle | + | * Undiluted coolant is underneath the sink. Mix the cool according to the ratio written on the bottle. |
| - | 17. Make sure all cabinets are locked and lockboxes are locked and closed | + | |
| - | 18. Turn off Keyence light, put black stage on, make sure 200x objective is in use | + | |
| - | 19. Clean the laser cutter | + | 17. Make sure all cabinets are locked and lockboxes are locked and closed. |
| + | |||
| + | 18. Turn off Keyence light, put black stage on, make sure 200x objective is in use. | ||
| + | |||
| + | 19. Clean the laser cutter. | ||
| * Take out the (layer with a bunch of hexagons) and vacuum small bits from the bottom. | * Take out the (layer with a bunch of hexagons) and vacuum small bits from the bottom. | ||
| - | 20. Clean laser cutter lens | + | |
| + | |||
| + | 20. Clean laser cutter lens. | ||
| * Tools in the laser cutter cabinet. | * Tools in the laser cutter cabinet. | ||
| * Place bubble wrap under the laser (in case of the lens drops). | * Place bubble wrap under the laser (in case of the lens drops). | ||
| Line 66: | Line 78: | ||
| * **NOTE**: The convex side of the lens will have a more prominent (relative to the concave side) dot in the center. | * **NOTE**: The convex side of the lens will have a more prominent (relative to the concave side) dot in the center. | ||
| * The grey knob on the laser will release the mirror for cleaning if necessary. | * The grey knob on the laser will release the mirror for cleaning if necessary. | ||
| + | |||
| + | |||
| 21. Ultimaker cleaning & Bambu cleaning | 21. Ultimaker cleaning & Bambu cleaning | ||
| * Clean out any scrap filament from the bottom of both printers. | * Clean out any scrap filament from the bottom of both printers. | ||
| * Make sure to wipe remaining glue on the Ultimaker platform by taking out the platform and using IPA. | * Make sure to wipe remaining glue on the Ultimaker platform by taking out the platform and using IPA. | ||
| - | * Clean the Bambu tray by removing and washing with warm water and soap | + | * Clean the Bambu tray by removing and washing with warm water and soap. |
| + | |||
| 22. Stratasys maintenance | 22. Stratasys maintenance | ||
| * Check the filament level, replace it with stock from the shelves in the corridor if necessary. | * Check the filament level, replace it with stock from the shelves in the corridor if necessary. | ||
| * To vacuum the print platform, go to settings and bring the gantry up; preferably use gloves. | * To vacuum the print platform, go to settings and bring the gantry up; preferably use gloves. | ||
| + | |||
| + | |||
| 23. SCA 1200HT maintenance | 23. SCA 1200HT maintenance | ||
| * Check for the fluid threshold level weekly. Over longer intervals, remove the container to check for parts in the cleaner (rotate 90 degrees to minimize splashing.) | * Check for the fluid threshold level weekly. Over longer intervals, remove the container to check for parts in the cleaner (rotate 90 degrees to minimize splashing.) | ||
| * **Note**: This device is particularly dangerous. Wear gloves, coat, and face shield when opening the door. Ask the manager or other WWs for detailed instructions. | * **Note**: This device is particularly dangerous. Wear gloves, coat, and face shield when opening the door. Ask the manager or other WWs for detailed instructions. | ||
| * **Note**: The alarm may sound if the container is lowered too quickly. Silence the alarm with the button that is indicated with a warning light but do so only if you are certain that this was the cause of the alarm. | * **Note**: The alarm may sound if the container is lowered too quickly. Silence the alarm with the button that is indicated with a warning light but do so only if you are certain that this was the cause of the alarm. | ||
| + | |||
| + | |||
| 24. Sweep and mop | 24. Sweep and mop | ||
| * Walkways and under benches. | * Walkways and under benches. | ||
| Line 84: | Line 104: | ||
| * **Rule of thumb**: Best to do in the mornings or weekends to avoid congestion in the lab. | * **Rule of thumb**: Best to do in the mornings or weekends to avoid congestion in the lab. | ||
| -------- | -------- | ||
| - | ==== Innovation Workshop | + | ==== 2442 Maintenance & Cleaning Manual ==== |
| 1. Check and replenish paper towels | 1. Check and replenish paper towels | ||
| * There are paper towel dispensers above every sink. | * There are paper towel dispensers above every sink. | ||
| - | * Extra paper towels can be found in uFl. | + | * Extra paper towels can be found in 3430. |
| 2. Check and replenish gloves | 2. Check and replenish gloves | ||
| - | * Extra boxes are located in uFl. | + | * Extra boxes are located in 3430. |
| 3. Replenish hazardous waste labels | 3. Replenish hazardous waste labels | ||
| * Empty solvent bottles should not be rinsed. Make sure to cross out the labels with a Sharpie and have a waste solvent label pre-tagged. | * Empty solvent bottles should not be rinsed. Make sure to cross out the labels with a Sharpie and have a waste solvent label pre-tagged. | ||
| Line 102: | Line 122: | ||
| * Organize scrap wood: put it on the shelf near lab coats. | * Organize scrap wood: put it on the shelf near lab coats. | ||
| * When cleaning the electronics workbench, clear any wires and tools from the bench and check to make sure that the soldering ions are turned off. | * When cleaning the electronics workbench, clear any wires and tools from the bench and check to make sure that the soldering ions are turned off. | ||
| - | 6. Make sure all power tools and cabinets are locked | + | 6. Make sure all power tools and cabinets are locked. |
| + | |||
| + | 7. Water jet maintenance | ||
| * Make sure the water jet is turned off and check if the abrasive needs to be restocked | * Make sure the water jet is turned off and check if the abrasive needs to be restocked | ||
| * Bags of abrasive are stored in the shipping/ | * Bags of abrasive are stored in the shipping/ | ||
| - | 7. Clean up sander/ | + | * Clean the inlets by rinsing them off and wiping off any metal on the magnet. |
| + | * Do an abrasive collect. | ||
| + | * Check that all abrasive collect spots (4 near each corner under the bed) are free of abrasive near the openings. You should use the water tube to blast away any abrasive and create a siphon with another tube so that the tool doesn' | ||
| + | 8. Clean up sander/ | ||
| * Use the paintbrush hanging with the tools and the vacuum to clean up debris. | * Use the paintbrush hanging with the tools and the vacuum to clean up debris. | ||
| - | 8. Clean and lubricate the mill and the lathe | + | 9. Clean and lubricate the mill and the lathe |
| * Vacuum away any chips and debris. | * Vacuum away any chips and debris. | ||
| * Oil using the oil bottle into all lubrication valves. | * Oil using the oil bottle into all lubrication valves. | ||
| - | 9. Clean the bandsaw and the drill press | + | 10. Clean the bandsaw and the drill press |
| * Use the vacuum. | * Use the vacuum. | ||
| * Ensure that you take the power supply off the drill press. | * Ensure that you take the power supply off the drill press. | ||
weekly_cleaning.1727126052.txt.gz · Last modified: 2024/09/23 21:14 by epace