Innovation Workshop Wiki

User Tools

Site Tools

Trace:
haas_mini_mill

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
haas_mini_mill [2022/08/26 23:16] – [Haas Super Mini Mill] haleyhaas_mini_mill [2024/09/26 19:42] (current) – epace
Line 1: Line 1:
 ====== Haas Super Mini Mill ===== ====== Haas Super Mini Mill =====
  
-8/26/22 Haley Holcomb haleyholcomb@ucsb.edu 
  
- +^                      Haas                             ^
-^                      Haas Super Mini Mill                             ^+
 |       {{ :tools:haasminimill:haas_mini_mill.jpg?nolink&200 |}}        | |       {{ :tools:haasminimill:haas_mini_mill.jpg?nolink&200 |}}        |
-| **Tool Type:**                  "CNC"                           | +| **Tool Type:**                  CNC                           | 
-| **Location:**                   "mFL 3430"                           |+| **Location:**                   Elings 3430                          |
  
  
-|  **Supervisor**        |  **Tool Lead**  |      
-|  David Bothman         |  David Bothman  | 
-|  (805) 893-4125        |  (805) 893-4125   | 
-|  bothman@cnsi.ucsb.edu  |  bothman@cnsi.ucsb.edu  | 
  
 | **Description:**                CNC milling machine                          | | **Description:**                CNC milling machine                          |
 | **Manufacturer:**               Haas                           | | **Manufacturer:**               Haas                           |
  
 +Last edited 8/26/22 Haley 
 ---- ----
  
 ===== About ===== ===== About =====
  
-The Haas Super Mini Mill is a CNC milling machine. Parts can be modeled in SOLIDWORKS and then toolpaths are programmed through an HSM add-in that generates G-code for the machine to read. The Haas can read  G-code and .EGC files. +The Haas Super Mini Mill is a CNC milling machine. Parts can be modeled in SOLIDWORKS and then toolpaths are programmed through an HSM add-in that generates G-code for the machine to read. The Haas can read  G-code and .EGC files. ** Due to its complexity, we do not offer regular training for this tool.** If you just need it for a few parts, please use our [[https://docs.google.com/forms/d/e/1FAIpQLSeQZ5JnKzOf-UZA0yWZ1XwLGQjmtgyEOFxxHWpZWUUIa8OxcA/viewform|Job Submission Google Form]] and we will machine them for you. If you believe you have a strong need to use this tool, please contact the lab manager. 
 +---- 
 + 
 +===== Safety Concerns ===== 
 +  * Safety Glasses must be worn when machine is running 
 +  * The glass doors must be in closed before starting a job 
 +  * The spindle must be completely stopped before adjusting or removing work piece or tool 
 +  * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper 
 +  * Proof your program before running it. The first time you run it, slow the rapid speed and stay by the control panel. It is a good idea to use single block mode the first time you run your program. 
 + 
 +---- 
 + 
 +===== Training Documentation ===== 
 + 
 +[[Haas Super Mini Mill Training SOP]] 
 + 
 +[[Haas mill setup checklist]] 
 ---- ----
  
Line 51: Line 63:
 ---- ----
  
-===== Safety Concerns ===== 
-  * Safety Glasses must be worn when machine is running 
-  * The glass doors must be in closed before starting a job 
-  * The spindle must be completely stopped before adjusting or removing work piece or tool 
-  * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper 
- 
- 
- 
----- 
- 
-===== Operating Procedures ===== 
-  - Program tool paths using a SOLIDWORKS add-in 
-  - Put tools in tool holders 
-  - Set tool offsets using tool probe 
-  - Set fixture offset(s) with touch probe (usually G54) 
-  - Load program 
-  - Check that tool numbers in program match tools in machine 
-  - Check that appropriate fixture offset is loaded 
-  - Load stock in the machine 
-  - Proof the part (test the program with air cuts). One easy way to do this is to add a height to the G54 Z value sufficient to make sure that all cuts will be above the top of the part surface. 
-  - Use rapid and feed override at the beginning of the program to make sure that the initial Z axis moves are safe. You can also use single block mode Keep your hand close to the emergency stop in case the program doesn’t do what you expect. 
-  - Reset G54 to the correct value. 
-  - Run the program for the first time - follow the precautions in step 10 to make sure that nothing unexpected happens. You can adjust the feed rate override as needed. 
- 
----- 
  
 ===== Reference Documentation ===== ===== Reference Documentation =====
Line 87: Line 74:
  
 {{:tools:haasminimill:programming_workbook.pdf|Programming Workbook}} {{:tools:haasminimill:programming_workbook.pdf|Programming Workbook}}
- 
------ 
- 
-===== Training Documentation ===== 
- 
-[[Haas Super Mini Mill Training SOP]] 
  
 [[RS232 file transfer documentation]] [[RS232 file transfer documentation]]
Line 98: Line 79:
 {{:tools:haasminimill:nexgen_cam_cnc_book.pdf|Haas / HSMWorks Intro Text}} {{:tools:haasminimill:nexgen_cam_cnc_book.pdf|Haas / HSMWorks Intro Text}}
  
-[[Haas mill setup checklist]]+----- 
  
----- 
  
haas_mini_mill.1661555788.txt.gz · Last modified: 2022/08/26 23:16 by haley