Differences

This shows you the differences between two versions of the page.

--- start [2023/09/11 18:54] – [Lab Announcements] bdincau
+++ start [2024/03/04 21:15] – [Lab Announcements] bdincau
@@ Line 10: / Line 10: @@
 ===== Lab Announcements =====
-/11/23 \\
+/04/24 \\
-The Trotec **laser cutter has been restored,** and may now be used again. After a thorough cleaning, we replaced the honeycomb bed and airjet lines. We also performed a few routine test cuts to make sure that the lens and positional accuracy were not affected.
+**The Innovation Workshop and Microfluidics Lab have been merged into one FBS facility.** Please ensure that you are working inside the new facility, appropriately named "Innovation Workshop & Microfluidics Lab". Let us know if you have any questions or notice anything missing.
-/09/23 \\
+{{ :announcements:fbs_facility_example.png?nolink&800| }} \\ \\ \\ \\ \\ \\ \\
-There was a small fire on the Trotec laser cutter over the weekend. The **laser cutter is currently blocked from reservations in FBS and cannot be used.** We will inspect & clean the tool on Monday morning and provide another update.
+/26/24 \\
-/01/23 \\
+The **waterjet is back**. After disconnecting, draining, then reconnecting the pump, the pressure came back up and stabilized. If you use the waterjet in the next few weeks, please pay attention to the flow rate. If it drops dramatically, accompanied by a water-hammer sound, please pause the cut and contact the lab manager.
-Have you ever wondered **which resin printer is best for your application?** Check out our new little study - {{wiki:3dprint:resin_print_resolution_summary.pdf | Resolution Limits and Print Quality for Resin Printers }}, where we compare the resolution limits of our Objet30 and Form3 printers.
+/23/24 \\
+The **waterjet is currently down.** The pump pressure is low and the pump is vibrating in an unhealthy way. We are working to restore the tool asap.
-/22/2023 \\
+/06/23 \\
-**Starting April 1st, a reservation will be required for any and all lab use.** Recharge will no longer be tied to door swipes, thus your compliance will be essential for accurate usage tracking and billing. If you are unfamiliar with making reservations in FBS, please see our [[fbs_reservation_information | tutorial]] and contact bdincau@ucsb with any questions or concerns.
+We now have a [[https://forms.gle/YvvXqV18izy4TumY6 | Microfluidics Lab & Innovation Workshop Feedback Form!]]
+Please use this form to let us know how we are doing, as well as provide suggestions for potential new tools or procedures.
+/18/23 \\
-/07/2023 \\
+**We have redesigned our silanization chamber.** The new chamber features polymer valves and fittings which should not corrode like the stainless steel fittings used in the previous chamber. The silane agent is also stored in a sealed glass container now, so we can easily see when it is running low. Please take a moment to [[vapor_silanation_rig_sop_new | review the new SOP]] before using the tool. Report any issue to the lab manager, and note them in the log book.
+/22/2023 \\
+**Starting April 1st, a reservation will be required for any and all lab use.** Recharge will no longer be tied to door swipes, thus your compliance will be essential for accurate usage tracking and billing. If you are unfamiliar with making reservations in FBS, please see our [[fbs_reservation_information | tutorial]] and contact bdincau@ucsb with any questions or concerns.
-Please take a moment to review the **upcoming changes to our [[2023_rates | recharge rates]]**.
 ===== Hotlinks for Submissions and Requests =====
@@ Line 63: / Line 72: @@
 Colin: ckwok520@ucsb.edu
-Andrew: andrewfurst@ucsb.edu
 Haley: haleyholcomb@ucsb.edu
@@ Line 70: / Line 77: @@
 Jason: jwei@ucsb.edu
-Vedad: vedad@ucsb.edu
+__Feedback__
+[[https://forms.gle/YvvXqV18izy4TumY6 | Microfluidics Lab & Innovation Workshop Feedback Form]]